background image

Printer connections

Connect the printers to the Control Center Microboard as follows. Only one printer can be

connected at a time.

Table 206: Okidata OKIPOS 441

Microboard

Printer

Function

J2-4

Pin 3

Tx (data to printer)

J2-2

Pin 20

DSR (busy signal from printer)

J2-9

Pin 7

Gnd

Cabinet

Shield

Hardware required:

Cable

#18 AWG stranded 50 ft. maximum length.

Connectors

Microboard

None. Strip 1/4" insulation from wire and insert into screw terminal block.

Printers

Okidata - 25 pin plug DB-25P or equivalent; Shell DB-C2-J9 or equivalent.

Printer setup

The selected printer must be configured as follows. Refer to manual provided by printer

manufacturer with respective printer.

Okidata OKIPOS 441

1. With the printer power off, remove the two screws which hold the RS232 Interface Module.
2. Pull the RS232 Interface Module out of the printer.
3. Set DIP switch SW2-2 to OFF to select 19200 BPS. Do not change any other switch settings.
4. Re-install the RS232 Interface Module and two mounting screws.
5. Load paper and install the printer ribbon into the printer.
6. Connect the printer cable to the printer and the microboard.
7. Connect the printer power cable to the printer and plug into a 100 to 240VAC power source.

Control center setup

Chiller ID

Access Level Required: OPERATOR
Using the COMMS Screen, assign an identification number to the chiller. This number will appear at

the top of each report.

Printer setup

Access Level Required: OPERATOR

YK-EP Style B Centrifugal Chiller

222

Содержание 160.87-OM1













































































































































































































































































Отзывы: