Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 93

Страница: 93 / 123

4-13

EJU00546a

Inspecting the steering cable

Check for smooth operation of the handle-

bars and jet thrust nozzle.

Turn the handlebars as far as possible to

the right and left and check that the differ-
ence of distance A and B between the jet
thrust nozzle and the nozzle is within 5 mm.

If steering is stiff or misadjusted, have a

Yamaha dealer service it.

Difference of A and B:

Maximum 5 mm (0.20 in)

EJU00550

Inspecting and adjusting the
throttle cable

Check that the throttle cable moves back

to the set position smoothly and that free
play is within specification.
1. Squeeze and release the throttle lever. If

the lever does not return smoothly, have
a Yamaha dealer service it.

2. Adjust free play

by loosening the lock-

nut

and turning the adjuster

Throttle lever free play:

4–7 mm (0.16–0.28 in)

Содержание WaveRunner GP800R 2001




























































































































Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы:

Yamaha WaveRunner GP800R 2001, Руководство владельца/оператора, Страница: 93 / 123

Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы: