Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 82

Страница: 82 / 123

4-2

1. Put the watercraft on land in a horizontal

position.

2. Open the flushing hose connector cap

and then insert the garden hose adapter

into the flushing hose connector

and

turn it until it is securely connected.

3. Connect the garden hose adapter to a

water tap using a hose.

4. Start the engine, and then immediately

turn the water supply on until water flows
out continually from the cooling water
pilot outlet.

5. Run the engine at idling speed for about

3 minutes watching the engine condition.
If the engine stops while flushing, turn
the water supply off immediately and
repeat the above steps.

6. Turn the water supply off, and then force

the remaining water out from the cooling
passages by alternately squeezing, and
releasing the throttle lever for 10 to
15 seconds.

7. Stop the engine.
8. Remove the garden hose adapter and

secure the cap.

Содержание WaveRunner GP800R 2001




























































































































Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы:

Yamaha WaveRunner GP800R 2001, Руководство владельца/оператора, Страница: 82 / 123

Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы: