Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 123

Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 88

4-8

E

NOTE:

A service manual is available for purchase
through a Yamaha dealer for owners who
have the mechanical skills, tools, and other
equipment necessary to perform mainte-
nance not covered by this Owner’s/Opera-
tor’s Manual.

Owner’s/Operator’s Manual
and tool kit

It is advisable always to carry the Owner’s/

Operator’s Manual and tool kit with you
whenever you use the watercraft. For your
convenience, a storage compartment

1

is

provided on the watercraft for the manual
and tool kit.

NOTE:

To protect these materials from water dam-
age, it would be a good idea to put them in a
waterproof bag. If your Owner’s/Operator’s
Manual is damaged, order a replacement
from a Yamaha dealer.

The service information included in this

manual is intended to provide you with the
necessary information for completing your
own preventive maintenance and minor
repairs. The tools provided in the tool kit

2

are sufficient for this purpose. However, a
torque wrench may also be necessary to
tighten nuts and bolts.

«
...
86
87
88
89
90
...
»

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов