Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 123

Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 81

4-1

E

EJU00516a

Storage

WARNING

Always place the fuel cock knob in the
“OFF” position when storing the water-
craft, otherwise fuel could leak out into
the engine or engine compartment,
which would create a fire hazard.

Storage for prolonged periods of time,

such as winter storage, requires preventa-
tive maintenance to ensure against deterio-
ration. It is advisable to have the watercraft
serviced by a Yamaha dealer prior to stor-
age. However, the following procedures can
be performed by the owner.

EJU00913a

Flushing the cooling system

Flushing the cooling system is essential

to prevent the cooling system from being
clogged with salt, sand, or dirt.

CAUTION:

●

Do not supply water to the cooling
water passages when the engine is not
running. The water could flow back
through the muffler into the crankcase
causing severe engine damage.

●

Do not run the engine for more
15 seconds without supplying water,
otherwise the engine may overheat.

«
...
79
80
81
82
83
...
»

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов