Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 27

Страница: 27 / 123

2-3

Engine shut-off cord (lanyard)

Attach to wrist so that the engine stops if the
operator falls off the watercraft.

Engine stop switch

Push to stop the engine normally.

Clip

Insert into the engine shut-off switch to enable
starting of the engine.
Remove to stop the engine or prevent acci-
dental starting of the engine or unauthorized
use of the watercraft.

Quick Shift Trim System (QSTS) selector

Use to select the trim angle of the watercraft.

Engine shut-off switch

Remove the clip to stop the engine and dis-
able it from starting.

Start switch

Push to start the engine.

Multifunction information center

Use to check watercraft operation.

Throttle lever

Use to accelerate and decelerate.

Choke lever

Oil tank filler cap

Fuel cock knob

Stern drain plugs

Use to drain water in the bilge when the water-
craft is on dry land.

Jet thrust nozzle

Changes the direction of jet thrust according
to handlebar position.

Ride plate

Содержание WaveRunner GP800R 2001




























































































































Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы:

Yamaha WaveRunner GP800R 2001, Руководство владельца/оператора, Страница: 27 / 123

Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы: