Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 43

Страница: 43 / 123

2-19

EJU00672a

Storage compartments

A front storage compartment and a glove

compartment are provided.

NOTE:

●

Make sure that the storage compartments
are properly secured before operating the
watercraft.

●

The storage compartments are not
designed to be waterproof. If you carry
objects that must be kept dry, such as the
manuals, put them in a waterproof bag.

Front storage compartment

The front storage compartment

located at the bow.

To open the front storage compartment,

push the hood latch

down, and then open

the hood.

NOTE:

The front storage compartment can be
removed to access the engine compartment.

Front storage compartment:

Capacity: 16 L (4.2 US gal, 3.5 Imp gal)
Load limit: 5 kg (11 lb)

To close the front storage compartment,

push down on the rear of the hood until it
latches securely.

Содержание WaveRunner GP800R 2001




























































































































Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы:

Yamaha WaveRunner GP800R 2001, Руководство владельца/оператора, Страница: 43 / 123

Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы: