Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 39

Страница: 39 / 123

2-15

EJU00698b

Multifunction information
center

This meter contains following functions for

the help and convenience of operation.

Tachometer

Speedometer

Fuel meter

Hour meter

Warning light

Oil warning indicator

Engine overheat warning indicator

Fuel warning indicator

Reset button

CAUTION:

●

Do not run the engine at full throttle or
more than 15 seconds to check the
meter for operation on land. The
engine could overheat.

●

Use the specified resistor-type spark
plug and cap, otherwise the meter may
function erratically.

NOTE:

All display light up and the buzzer sounds
twice after the engine starts. Then, the
meter will operate normally after few sec-
onds. The current display will continue to
operate for 30 seconds after the engine
stops.

Содержание WaveRunner GP800R 2001




























































































































Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы:

Yamaha WaveRunner GP800R 2001, Руководство владельца/оператора, Страница: 39 / 123

Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы: