Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 123

Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 16

1-12

E

EJU00313

Hazard information

●

When transporting or storing your water-
craft, always place the fuel cock knob in
the “OFF” position, otherwise gasoline
may overflow from the carburetor.

●

Never start the engine or let it run for any
length of time in an enclosed area.
Exhaust fumes contain carbon monoxide,
a colorless, odorless gas that may cause
loss of consciousness and death within a
short time. Always operate the watercraft
in an open area.

EJU00315a

Watercraft characteristics

●

Jet thrust turns the watercraft. Releasing
the throttle completely produces only min-
imum thrust. If you are traveling at speeds
above trolling, you will have rapidly
decreasing ability to steer without throttle.
You may still have some turning ability
immediately after releasing the throttle,
but once the engine slows down, the
watercraft will no longer respond to han-
dlebar input until you open the throttle
again or you reach a trolling speed. Prac-
tice turning in an open area without
obstructions until you have a good feel for
this maneuver.

●

This watercraft are water-jet propelled.
The jet pump is directly connected to the
engine. This means that jet thrust will pro-
duce some movement whenever the
engine is running. There is no “neutral”
position.

●

Keep away from intake grate

1

while the

engine is on. Items such as long hair,
loose clothing, or PFD straps can become
entangled in moving parts resulting in
severe injury or drowning.

●

Never insert any object into the jet thrust
nozzle

2

while the engine is running.

Severe injury or death could result from
coming in contact with the rotating parts
of the jet pump.

«
...
14
15
16
17
18
...
»

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов