manualshive.com logo in svg

Yamaha WaveRunner GP800R 2001, Руководство владельца/оператора, Страница: 62 / 123

Поделиться
Скачать
Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 62

3-16

E

2. Turn the fuel cock knob to the “ON” posi-

tion.

NOTE:

Before starting the watercraft, after it has
been sitting, remove the fuel tank filler cap
to release any built-up pressure in the tank
due to fuel expansion.

3. Attach the clip 

1

 to the engine shut-off

switch 

2

. Also, attach the engine shut-

off cord 

3

 to your left wrist.

WARNING

Check that the engine shut-off cord is not
frayed or broken, and keep it free from
the handlebars so the engine stops if the
operator falls off. The engine shut-off
cord may not pull free if wrapped around
the handlebars when the operator falls
off, allowing the watercraft to continue to
run and cause an accident.

NOTE:

It is not possible to start the engine with the
clip removed from the engine shut-off
switch.

4. Move the choke lever all the way in the

direction of the arrow to start a cold
engine.

NOTE:

The choke should not be used when the
engine is warm.

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов