Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 32

Страница: 32 / 123

2-8

EJU00705

Engine stop switch

Push this switch

(red button) to stop

the engine normally.

EJU00706

Engine shut-off switch

Insert the clip

, on the end of the engine

shut-off cord

, under the engine shut-off

switch

(black button). The engine will stop

automatically when the clip is removed from
the switch, such as if the operator falls off
the watercraft.

WARNING

●

Always attach the engine shut-off cord
to your wrist and the clip to the engine
shut-off switch BEFORE starting the
engine.

●

To prevent accidental starting of the
engine or unauthorized use by chil-
dren or others, always remove the clip
from the shut-off switch when the
engine is not running.

EJU00350

Choke lever

Starting a cold engine requires a richer

air-fuel mixture, which is supplied by the
choke.

Move the lever

in direction

to turn

the choke on.

Move the lever in direction

to turn the

choke off.

Содержание WaveRunner GP800R 2001




























































































































Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы:

Yamaha WaveRunner GP800R 2001, Руководство владельца/оператора, Страница: 32 / 123

Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы: