manualshive.com logo in svg

Yamaha WaveRunner GP800R 2001, Руководство владельца/оператора, Страница: 55 / 123

Поделиться
Скачать
Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 55

3-9

E

F0P03010

EJU00728

Fire extinguisher

Check that there is a full fire extinguisher

on board. The fire extinguisher container 

1

is located in the battery compartment.

To open the fire extinguisher container

cap

2

 remove the seat and turn it counter-

clockwise.

After inserting the fire extinguisher make

sure that the container cap is tightened
securely.

NOTE:

●

See the instructions supplied by the fire
extinguisher manufacturer for checking
the fire extinguisher. Always keep the
extinguisher in the fire extinguisher con-
tainer.

●

Always carry a fire extinguisher on board.
A fire extinguisher is not standard equip-
ment with this watercraft. If you do not
have one, contact a Yamaha dealer or a
fire extinguisher dealer to obtain one
meeting the proper specifications.

Fire extinguisher:

Classification: B-1
Capacity: 2 lb or more

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов