Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 41

Страница: 41 / 123

2-17

YAMAHA

MPH

FUEL

HOUR

x1000r/min

MULTI

DISPLAY

F0X0232

EJU00386a

Fuel meter

The fuel meter is provided for convenient

fuel level checking while riding. The fuel
meter has eight segments which show the
amount of fuel remaining in the fuel tank.

NOTE:

The indication of the segments differs on
your operating condition. Use the meter as a
reference.

EJU00390a

Hour meter

The hour meter is provided to make it

easy to follow the maintenance schedule.
The meter shows the hours of engine opera-
tion that have elapsed since the watercraft
was new.

NOTE:

●

The elapsed time will be kept even if the
battery terminals have been discon-
nected.

●

If the hour meter malfunctions, “_ _ _ _”
display and the warning light will blink.

Содержание WaveRunner GP800R 2001




























































































































Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы:

Yamaha WaveRunner GP800R 2001, Руководство владельца/оператора, Страница: 41 / 123

Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы: