Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 123

Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 31

2-7

E

EJU00704

Fuel cock knob

The fuel cock supplies fuel from the fuel

tank to the carburetors.

The fuel cock knob

1

positions are

explained as follows and are shown in the
illustration.

OFF:

With the fuel cock knob in this position,

fuel does not flow. Always turn the fuel cock
knob to this position when the engine is not
running.

ON:

With the fuel cock knob in this position,

fuel flows to the carburetors. Turn the fuel
cock knob to this position when starting the
engine and operating the watercraft.

RES:

This indicates reserve. With the fuel cock

knob in this position, the fuel reserve is
made available. Turn the fuel cock knob to
this position if you run out of fuel while oper-
ating the watercraft. When this occurs,
refuel as soon as possible and be sure to
turn the fuel cock knob back to “ON”!

«
...
29
30
31
32
33
...
»

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов