Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 123

Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 87

4-7

E

EJU00535a

Maintenance and

adjustments

Periodic inspection, adjustment and lubri-

cation will keep your watercraft in the safest
and most efficient condition possible. Safety
is an obligation of the watercraft owner. The
most important points of watercraft inspec-
tion, adjustment and lubrication are
explained on the following pages.

See your Yamaha dealer for genuine

Yamaha replacement parts and optional
accessories designed for your watercraft.

Remember that failures that are the result

of the installation of parts or accessories
which are not qualitatively equivalent to gen-
uine Yamaha parts are not covered by the
limited warranty.

WARNING

●

Be sure to turn off the engine when
you perform maintenance unless oth-
erwise specified, otherwise an acci-
dent or injury could result from
unexpected operation, moving parts,
or electric shock. If the owner is not
familiar with watercraft servicing, this
work should be done by a Yamaha
dealer. Improperly serviced compo-
nents could fail or stop operating cor-
rectly, which could result in an
accident.

●

Modifications to this watercraft not
approved by Yamaha may cause loss
of performance or excessive noise, or
render it unsafe for use. Consult a
Yamaha dealer before attempting any
changes.

«
...
85
86
87
88
89
...
»

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов