Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 123

Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 112

5-6

E

EJU00600

Connecting the jumper cables

1. Connect the positive (+) jumper cable

1

to the positive (+) terminals of both bat-
teries.

2. Connect one end of the negative (–)

jumper cable

2

to the negative (–) termi-

nal of the booster battery

3

.

3. Connect the other end of the negative (–)

cable to an unpainted bolt on the cylinder
head.

CAUTION:

Do not connect the end of the jumper
cable to the negative (–) terminal on the
watercraft battery! Be sure all connec-
tions are secure and correct before
attempting to start the engine. Any
wrong connection may damage the elec-
trical system.

4. Start the engine, and then disconnect

the cables by reversing the steps above.

CAUTION:

●

Never push the start switch while the
engine is running.

●

Do not operate the start switch for
more than 5 seconds, otherwise the
battery will be discharged and the
engine will not start. Also, the starter
motor may be damaged. If the engine
does not start in 5 seconds, release
the start switch, wait 15 seconds, and
try again.

«
...
110
111
112
113
114
...
»

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов