Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 114

Страница: 114 / 123

5-8

EJU00604a

Submerged watercraft

If the watercraft is submerged or flooded

with water, follow the procedure below and
consult a Yamaha dealer as soon as possi-
ble. Failure to do so may result in serious
engine damage!
1. Beach the watercraft and remove the

stern drain plugs to drain the water from
the engine compartment.

2. Turn the fuel cock knob to “OFF.”
3. Remove the spark plugs and dry them

with a cloth.

4. Without reinstalling the spark plugs,

crank the engine until all the water in the
cylinders has been drained.

5. Install the stern drain plugs and the

spark plugs.

6. Turn the fuel cock to “ON.”
7. Launch the watercraft into the water, and

then run the engine for at least
10 minutes. If the engine will not start,
repeat steps above.

8. Turn the engine off. Turn the fuel cock to

“OFF.”

9. Remove the silencer caps and spray a

rust inhibitor such as Yamaha Stor-Rite
Engine Fogging Oil into the carburetor
while cranking the engine.

10. Have the watercraft inspected by a

Yamaha dealer as soon as possible.

Содержание WaveRunner GP800R 2001




























































































































Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы:

Yamaha WaveRunner GP800R 2001, Руководство владельца/оператора, Страница: 114 / 123

Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы: