Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 123

Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 76

3-30

E

EJU00635

Beaching the watercraft

1. Make sure no obstructions, boats or

swimmers are near the beach. Release
the throttle lever about 110 m (360 ft)
before you reach the intended beaching
area.

2. Approach the beach slowly and stop the

engine before reaching land. Remem-
ber: you need throttle to steer.

3. Get off the watercraft and pull it up on

the beach.

CAUTION:

Small pebbles, sand, seaweed, and other
debris can be pulled into the jet intake
and impair or damage the impeller.
Always stop the engine and get off
before beaching the watercraft.

EJU00505

Docking the watercraft

1. Make sure that no obstructions, boats or

swimmers are close to the watercraft.
Reduce speed about 110 m (360 ft)
away from the dock.

2. Slowly approach the dock and stop the

engine just before coming alongside it.

EJU00507

Rough water operation

The force of landing after jumping can

cause a strong impact on both the watercraft
and the operator and passenger. It is possi-
ble for the operator to hit his or her chest or
jaw on the watercraft body or handlebars
and be injured. Do not operate the water-
craft with your chin right above the handle-
bars or with your feet outside the watercraft.
Operating in rough water or jumping waves
can also crack the watercraft body or dam-
age internal parts. Avoid operating in rough
water or bad weather conditions.

«
...
74
75
76
77
78
...
»

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов