Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 123

Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 59

3-13

E

EJU00676a

Operation

WARNING

Before operating your watercraft,
become familiar with all controls. Con-
sult your Yamaha dealer about any con-
trol or function you do not fully
understand. Failure to understand how
controls work could cause an accident or
prevent you from avoiding an accident.

CAUTION:

Make sure that stern drain plugs are
securely tightened before launching the
watercraft.

EJU00459

Engine break-in

The engine break-in period is essential to

allow the various components of the engine
to wear and polish themselves to the correct
operating clearances. This ensures proper
performance and promotes longer compo-
nent life.

CAUTION:

●

For the first tankful of operation, pre-
mix a 50:1 mixture of fuel and oil (in
addition to the oil in the oil tank).

●

After break-in, use straight gasoline
for normal operation.

1. Launch the watercraft and start the

engine. (See pages 3-15 to 3-17 for
engine starting procedures.)

2. Run the engine at the lowest possible

speed for 5 minutes.

«
...
57
58
59
60
61
...
»

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов