Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 123

Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 50

3-4

E

EJU00324a

2-stroke engine oil

If YAMALUBE 2-W is not available,

another 2-stroke engine oil with an NMMA-
certified TC-W3 rating may be used.

Recommended engine oil:

YAMALUBE 2-W

EJU00419a

Filling the oil tank

WARNING

●

Do not add gasoline to the oil tank.
Fire or explosion could result.

●

Oil in the bilge is a serious fire hazard.
Wipe up any spilled oil immediately.

CAUTION:

Do not allow the oil tank to become com-
pletely empty. If the oil tank becomes
empty the oil injection pump must be
bled to ensure proper oil flow, otherwise
engine damage may occur. If bleeding of
the oil pump is necessary, have a
Yamaha dealer bleed it.

1. Remove the seat to watch the oil level.

(See page 2-5 for seat.)

2. Open the oil tank filler cap, and very

slowly add engine oil to the oil tank.

3. Stop filling when the oil just reaches the

top of oil tank visible.

Oil tank capacity:

5.5 L (1.45 US gal, 1.21 Imp gal)

«
...
48
49
50
51
52
...
»

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов