Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 90

Страница: 90 / 123

4-10

EJU00537

Inspecting the fuel system

WARNING

Gasoline and its vapors are highly flam-
mable and explosive.

Check the fuel system for leaks, cracks,

or malfunctions. If any problem is found, do
the necessary repair or replacement as
required. If repair is necessary, consult a
Yamaha dealer.

Check:

●

Carburetor for leakage.

●

Fuel pump for malfunction or leakage.

●

Fuel tank for water or dirt.

●

Fuel tank for damage, cracks or leakage.

●

Fuel hose joint for leakage.

●

Fuel hose for cracks or other damage.

●

Fuel filter for leakage.

●

Fuel cock for leakage.

●

Air vent check valve for leakage.

●

Fuel tank filler cap for damage.

WARNING

Failure to check for and repair any fuel
leakage may result in fire or explosion.

Содержание WaveRunner GP800R 2001




























































































































Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы:

Yamaha WaveRunner GP800R 2001, Руководство владельца/оператора, Страница: 90 / 123

Результаты поиска

Содержание WaveRunner GP800R 2001

Отзывы: