Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 123

Yamaha WaveRunner GP800R 2001 Скачать руководство пользователя страница 42

2-18

E

YAMAHA

8

7

6

5

4

3

2

1

MPH

FUEL

HOUR

x1000r/min

MULTI

DISPLAY

WARNING

F0X0233

YAMAHA

8

7

6

5

4

3

2

1

MPH

FUEL

HOUR

x1000r/min

MULTI

DISPLAY

WARNING

F0X0234

YAMAHA

8

7

6

5

4

3

2

1

MPH

FUEL

HOUR

x1000r/min

MULTI

DISPLAY

WARNING

F0X0235

EJU00716a

Fuel warning indicator

If the fuel remaining in the tank drops to

about 13 L (3.4 US gal, 2.9 lmp gal), the
lowest two fuel level segments, the fuel
warning indicator and the warning light
begin to blink. The buzzer also starts sound-
ing intermittently.

The warning signals will be cleared when

the engine restarts after refilling fuel.

EJU00717a

Oil warning indicator

If the oil remaining in the tank drops to

about 1.7 L (0.45 US gal, 0.37 lmp gal) or
the oil filter is clogged, the oil warning indi-
cator and the warning light begin to blink.
The buzzer also starts sounding intermit-
tently.

If the oil warning indicators begin to blink,

refill with engine oil as soon as possible.

The warning signals will be cleared when

the engine restarts after refilling engine oil.

NOTE:

If the warning indicators blink with adequate
oil in the tank, check the oil filter for clog-
ging.

EJU00718a

Engine overheat warning
indicator

If the engine starts to overheat, the

engine overheat warning indicator and the
warning light begin to blink. The buzzer also
starts sounding.

«
...
40
41
42
43
44
...
»

Содержание WaveRunner GP800R 2001




























































































































Отзывы:

Нет отзывов