ENGLISH
10
PREPARATION FOR FIRST OPERATION
Bleeding Air from the Fuel Lines
3
CAUTION:
To avoid personal injury:
¡
Always keep the air bleeding
plug on the fuel filter closed
except when bleeding the air.
¡
D O N O T p e r f o r m b l e e d i n g
operation when engine is hot.
NOTE:
Always bleed the air completely in the following
circumstances.
¡
When adding fuel into an empty tank.
¡
When refueling after the engine stops after
running completely out of fuel.
¡
Whenever the fuel system is drained for fuel filter
cleaning or other fuel system servicing.
1.
Fill the fuel tank with fuel.
2.
Turn the fuel tank tap open.
3.
Open the air bleeding plug on the fuel filter.
4.
If a clear flow of fuel from the plug, close it
immediately.
(1) Air bleeding cock
(A) “OPEN”
(2) Fuel filter cartridge
(B) “CLOSE”
5.
Rotate the engine for about 30 seconds, and then
stop the engine.
6.
Wipe up any spilled fuel immediately.
PREPARATION TO SUPPLY THE ELECTRIC
POWER
1. Generator Grounding
The end user, equipment owner or operator must
contact his local, state, county or municipal electric
code department to determine the approved
generator grounding method to be used in his
application or location.
Recommendations in the NEC, NFPA AUSTRALIAN
STANDARDS and OSHA regulations must be
followed to assure compliance and safe operation.
A grounding lug is provided on the Kubota generator
frame for earth grounding depending on local, state,
national or OSHA requirements.
One possible connection method for construction site
use is as follows:
(1) Load center cover
(A) #6AWG
(2) Generator
Flexible copper
ground terminal
ground connection
(B) Metal ground
rod or building
cold water
pipe system
per N.E.C.
code
TIP
YAMAHA
WARNING
9CGNO̲E̲p00-40.indd 26
9CGNO̲E̲p00-40.indd 26
2009/12/18 16:56:45
2009/12/18 16:56:45
Содержание EDL13000SDE
