![background image](http://html1.mh-extra.com/html/xyz-machine-tools/trak-2op-m11-mill/trak-2op-m11-mill_safety-installation-maintenance-service-and-parts-list_3848763092.webp)
88
XYZ Machine Tools Ltd
TRAK
2
OP
Installation, Maintenance, Service & Part List Manual
5.11.4.3
Code 79:
Beeper On
This turns on the beeper for the control keys.
5.11.4.4
Code 80:
Beeper Off
This turns off the beeper for the control keys.
5.11.4.5
Code 203: Initiate Homing Sequence
This service code allows the user to home the machine. Normally, homing should be done on the first
screen when the control boots up. You cannot run the machine until the machine is homed.
5.11.4.6
Code 300: Set Lube Pump
Allows user to run the lube pump manually and adjust frequency and discharge times. Although, these are
factory set and should not need to be changed.
5.11.4.7
Code 345: Set Part Program Location
Allows the user to save programs to a USB device or to a network. See the 2 OP Programming and User
Manual for more information on networking the ProtoTRAK TMX control.
5.11.4.8
Code 503: Set Maximum Feedrate
Sets the maximum feedrate limit that the machine will run at. This affects programmed feedrates and rapid
feedrates. Can be set in inches per minute or millimeters per minute. The maximum feedrate is 600 ipm or
15240 mm/min
5.11.5
Group E - Critical Service Codes that Must Be Performed
The following table summarizes the critical service codes that must be performed after working on certain
aspects of the machine.
Service Code
When
Consequence
500
Setting ball lock
locations for X and Y
1.
Motor removed or replaced
2.
Motor belt slips
3.
Home switch replaced or a major mounting
adjustment is made.
4.
Home switch cam replaced or a major
adjustment is made
5.
Ballscrew replaced
6.
Angular contact bearings on motor end
replaced
7.
Table removed from machine and hence
separated from linear guides
8.
Computer module or compact flash has been
replaced and the configuration file was not
loaded into the new computer.
The X and/or Y offsets
saved with the users
programs could now be off
as much as 6 mm or 0.236”.
These items only apply
when working on the X or Y
axis
505
Checking the motor
index angle. Must be
set to 180º ±45º
1.
Motor removed or replaced
2.
Motor belt slips
3.
Home switch replaced or a major mounting
adjustment is made.
4.
Home switch cam replaced or a major
adjustment is made
5.
Ballscrew replaced
6.
Angular contact bearings on motor end
replaced
This code applies to any
work done to the X, Y or Z
axis
As a secondary item, you
should rerun this same code
and reset the soft limits
510
Setting the spindle
orientation angle
1.
Spindle motor has been removed, replaced
or motor coupling has slipped during
operation
The user will most likely
break a finger on the ATC.
More severe damage could
also occur which could be
costly to the user
Содержание TRAK 2OP M11 Mill
