![background image](http://html2.mh-extra.com/html/xerox/nuvera-100/nuvera-100_service-manual_3392260185.webp)
Cleaning and Maintenance
5-5
Vacuum
Vacuum dust from the top cover, the metal heat shield over the
printhead and plastic dust cover under the stripper fingers. Dust
should also be vacuumed from the vents, near the fans and anywhere
else where it is observed.
Drum Temperature Sensor
With a dry swab, clean any buildup around the drum temperature
sensor. You can access the sensor through the opened stripper finger
cover. Also make sure the sensor rides evenly on the drum surface.
You can remove the sensor, if necessary, to clean under it.
Maintenance
Maintenance roller
The printer uses the maintenance roller as part of its self-
maintenance routine to coat the print drum with oil before each print.
The maintenance roller (and its counter) must be replaced after
15,000 prints (the starter maintenance roller must be replaced after
7,500 prints). A front panel message indicates when the maintenance
roller is low. Printing is still possible when the maintenance roller
fluid is low. When a front panel message indicates the maintenance
roller is “empty,” the maintenance roller and its counter must be
replaced before continued printing is possible. Refer to the
instructions included with the kit to replace the maintenance roller
kit.
NOTE: The Drum Maintenance Unit Replacement Kit has a one year
shelf life.
NOTE: The drum fluid, an oil, poses no known adverse health effects.
Refer to the Material Safety Data Sheet for more information.
Содержание Nuvera 100
