![background image](http://html2.mh-extra.com/html/xerox/nuvera-100/nuvera-100_service-manual_3392260186.webp)
5-6
iiLINX™ Solid Inkjet 100 Service Manual
The number of remaining cycles can be obtained from the front panel
as follows.
1.
Allow the printer to warm up to its idle, “Ready to Print,” state.
2.
Scroll to the Info selection and press the Select button.
3.
Repeat for the menus Consumables and Maintenance Kit
Information.
4.
Scroll to the item Prints remaining. The number of remaining
oiling cycles is displayed following the colon.
When the number of remaining oiling cycles reaches 1000, the front
panel automatically displays the count as part of status message
indicating that the maintenance kit is low. A replacement kit should
be ordered at this time. The kit-low message remains, counting down
the number of remaining oiling cycles, until the count reaches 0. At
that point, the message is updated, stating that the kit is empty and
requires replacement. The printer will no longer print until the
maintenance drawer is replaced.
The front panel messages are accompanied by similar messages
emitted over the back-channel. These are “maintenance kit low” and
“maintenance kit exhausted.” While the drawer is in the process of
being replaced (that is, whenever it is removed), the back-channel
emits “maintenance kit missing.”
In addition, one other back-channel message is associated with the
maintenance drawer. The message is “waste liner full: please empty.”
This indicates the waste-ink tray must be emptied before normal
operation will resume. For quick reference, the front panel displays
additional instruction.
Waste Tray
The maintenance drawer contains a waste tray that collects the ink
that has been purged from the printer’s ink jets. The waste tray
should be emptied each time the maintenance drawer is removed
from the printer. Refer to “Emptying the Waste Tray,” in the
iiLINX™ Solid Inkjet 100 User Manual for instructions on removing
and emptying the waste tray. Be sure to insert the waste tray into
the maintenance drawer before reinstalling the maintenance drawer
in the printer. Never reuse waste ink in the printer.
Содержание Nuvera 100
