![background image](http://html2.mh-extra.com/html/xerox/nuvera-100/nuvera-100_service-manual_3392260157.webp)
Adjustments
4-13
3.
Remove the ink loader and the metal heat cover.
4.
Tilt the printhead to its print position and, if removed, attach
the head tilt spring.
5.
Torque the mounting screws to 20 in/lbs.
6.
Install the digital gap indicator and bracket to the left side of
the printer frame and tilt arm as described in the Procedure
“Mounting the Digital Indicator Gauge”. Ensure the digital
indicator is set to inches, “in.”
NOTE: Always move the printhead by moving the tilt arm.
7.
At the left side of the printhead, insert the left printhead
spacer between the printhead and the drum. Check the
indicator, it should read 0.0030 + / - 0.0010 inches. Adjust the
printhead’s spacing adjustment by twisting a flat-blade
screwdriver in the adjustment slot to move the printhead’s
position until the indicator reads the correct value.
NOTE: Do not insert both spacers at the same time as this will only
measure the larger of the two gaps.
8.
Remove the left printhead spacer and install the right spacer
between the printhead and the drum. Repeat the adjustment.
Confirm the left side is still in adjustment. If not, alternate
between the two sides until both sides read 0.0030
±
0.0010
inches.
9.
Remove the spacers. Snug the four locking screws using an X
pattern.Then tighten the four screws, using the same X
pattern, to 20 in.-lbs.
10.
Plug the printhead’s data ribbon cable and power wiring
harness into the power control board and the printhead.
Inspect both ends of the data ribbon cable to ensure they are
properly seated. Reconnect the two printhead ground wires to
the printer frame.
11.
Perform the “Hot Printhead-to-Drum Spacing Adjustment” to
set the correct gap between the “hot” printhead and the drum.
Содержание Nuvera 100
