3-32
ii LINX™ Solid Inkjet 100 Service Manual
5. Set the PC’s comm port to COMM1. Set the baud rate to 19.2
kbaud, 8 data bits, 1 stop bit and no parity.
6. In your DOS window, go to the
C:\
prompt.
7. To install the diagnostics from a diskette onto your computer,
type:
A:INSTALL /all <return>
.
8. Connect to the directory containing the diagnostic software
(
C:\100DIAGS)
. Launch the diagnostics program by typing
diags xxx,
where
xxx
is the name of the print engine
firmware level. (Typing
diags
lists the available diagnostic
versions.) Once launched, the program repeatedly attempts to
communicate with the printer. The link status indicator, in the
bottom-right corner of the screen, reads “NO” until this link is
established; once communication is established, it reads “OK.”
NOTE: The Comm Port should be set to 57.6 kb after communication
is established with the printer. The baud rate can be set faster for
quicker test downloading. If the printer’s power is cycled, the PC’s
baud rate must be reset to 19.2 Kb to reestablish communication with
the printer.
PC-based Diagnostics Screen Display
Once communication with the printer is made, the diagnostics display
the startup screen on the computer.
Содержание Nuvera 100
