![background image](http://html2.mh-extra.com/html/xerox/nuvera-100/nuvera-100_service-manual_3392260170.webp)
4-26
ii LINX™ Solid Inkjet 100 Service Manual
X-axis Scale Adjustment
This adjustment sets the gain or rate-of travel of the printhead’s X-
axis movement.
1. Allow the printer to warm up to its idle, “Ready to Print,” state.
2. Enter the “hidden” service menu by scrolling to the Service
Support menu and pressing the Select button. Then press
and hold the Left arrow button and, while holding the Left
arrow button, press the Select button.
3. Scroll to the menu item Adjust X-Axis Scale and press the
Select button. Scroll to the menu item Print Subjective Test
Pattern and press the Select button.
4. The print features four gray columns, each containing a jagged
black band. The black bands should all align vertically with
each other.
5. If an adjustment is needed, scroll to the menu item Set X-Axis
Scale. Change the displayed value to a new value, if necessary.
Increasing the scale value raises the two center black bars.
Decreasing the scale value lowers the two center black bars.
6. Select the menu item Print Subjective Test pattern to verify
the adjustment. Repeat the adjustment, if necessary.
Try to align the two center black bands and the two outer black
bands within one tick mark on the vertical scale.
0388-67
Increase scale
adjust to raise
center bars
Correct
Decrease scale
adjust to lower
center bars
Figure 4-11. Adjusting the X-axis Scale Adjustment
NOTE: The X-Axis Scale Adjustment menu also includes the item for
printing the Objective Test pattern. This pattern is only useful at the
factory. The Subjective Test pattern should be used instead.
Содержание Nuvera 100
