Removal and Replacement
6-27
Reverse these steps to install the drum/transfix assembly.
NOTE: Upon reassembly, install the hex-keyed screws first; they align
the drum/transfix assembly to the engine frame.
Make these adjustments after installing a new drum.
1. Ensure the drum position encoder sensor gap.
2. Set the Y-belt tension; refer to the topic “Y-axis Belts Tension
Adjustment”
3. Power up the printer in Bypass Mode to skip the startup and
mud pages.
4. Enter the hidden Service menu and select Seal Drum to seal
the new drum.
5. Perform the printhead to drum adjustment described in the
topic “Printhead-To-Drum Spacing Adjustment.”
Drum Position Sensor Assembly
1. Remove the left cover.
2. Remove the top cover.
CAUTION
Unhook the head tilt spring to avoid possible damage to the
printhead and drum.
3. Disconnect the drum home-position sensor wiring harness from
J180 of the left I/O board leading to the drum position
assembly. Disconnect the drum position encoder sensor at the
drum position assembly.
4. Remove the clear plastic dust cover from the drum position
assembly.
5. Precisely mark the end of the drum shaft relative to the drum
home flag on the drum position sensor assembly; this is not
necessary if you are also replacing the drum (as part of the
drum/transfix assembly).
Содержание Nuvera 100
