Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 105

Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 95

Alignment

Blade Guide Arm Alignment

Alignment

15doc080213

6-7

6

NOTE:

It is not necessary to align the spring bolt (bolt M10x75 [WM# F81003-15] + spring

+ washer) shown in the figure above. When replacing the bolt or spring, just screw in the bolt
completely.

6.5

Blade Guide Arm Alignment

Before aligning the blade guide arm, track the blade on the blade wheels as described in

. Move the carriage so the blade is positioned over the first bed rail. Level the blade to the bed

rail as shown in

. Adjust the blade guide rollers so they do not touch the blade.

Vertical Alignment

1.

Adjust the blade guide arm all the way out away from the other blade guide (maximum distance
between the guide rollers).

See Figure 6-8.

2.

Use the arm adjustment screws, marked with blue arrows in the figure above, to adjust the arm up
until the slide pad touches the saw head brace tube. Tighten the jam nuts.

3.

Adjust the blade guide arm in all the way toward the other blade guide (minimum distance between
the guide rollers).

4.

Use the arm adjustment screws, marked with red arrows in the figure above, to adjust the arm up
until the slide pad touches the saw head brace tube. Tighten the jam nuts.

NOTE:

When adjusting the blade guide arm screws, be careful not to tighten the screws too much

or put the arm in a bind. Operate the blade guide arm knob to ensure the arm moves easily in and
out when the knob is turned.

FIG. 6-8

150128_C

Adjust front top and bottom

screws with arm open

Adjust rear top and bottom

screws with arm closed

«
...
93
94
95
96
97
...
»

Содержание LT15M2 D10










































































































Отзывы:

Нет отзывов