Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 99

Страница: 99 / 105

Alignment

Blade Guide Spacing

Alignment

15doc080213

6-11

See Figure 6-12.

Move the carriage forward so the back end of the tool is over the bed rail.

Use the set screws shown to adjust the blade guide tilt until the measurement from the bed rail to
the tool equals the other two measurements taken.

10.

Move the tool close to the other blade guide and repeat the previous steps.

NOTE:

If major adjustments to blade guide tilt were made, remeasure the distance between the

blade and the bed rails to ensure the correct 1/4" (6.5 mm) blade guide deflection. Adjust if
necessary.

6.9

Blade Guide Spacing

HINT:

When adjusting blade guide spacing, loosen the top set screw and one side set screw only.

This will insure horizontal and vertical tilt adjustments are maintained when the set screws are
retightened.

Adjust the inner blade guide so the blade guide flange is approximately 1/16" - 1/8" (1.5 - 3.0 mm)
from the back of the blade.

Loosen one side and one top set screw shown. Tap the blade guide forward or backward until
properly positioned.

FIG. 6-12

SM0070

Loosen jam nuts and turn screws

to tilt roller up or down

Содержание LT15M2 D10










































































































Результаты поиска

Содержание LT15M2 D10

Отзывы:

Wood-mizer LT15M2 D10, Руководство пользователя, Страница: 99 / 105

Результаты поиска

Содержание LT15M2 D10

Отзывы: