Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 93

Страница: 93 / 105

Alignment

Blade Wheel Alignment

Alignment

15doc080213

6-5

Recheck the vertical tilt of the idle-side blade wheel with the blade guide alignment tool. Readjust
the blade wheel as necessary until the front and rear of the tool are the same distance from the bed
rail (within 1/16" [1.5 mm]).

Check the position of the blade on the idle-side blade wheel.

See Figure 6-5.

The horizontal tilt of the blade wheel should be adjusted so that the gullet of an

1-1/4" blade is 1/8" (3 mm) out from the front edge of the wheel (±1/32 [0.75 mm]).

See Figure 6-6.

Use the cant control adjustment to adjust the idle-side blade wheel. If the blade is

too far forward on the wheel, turn the cant control counterclockwise. If it is too far back on the
wheel, turn the cant control clockwise.

FIG. 6-4

FIG. 6-5

Adjust vertical adjust-

ment screws up to tilt

idle-side blade wheel

down; Adjust screws

down to tilt wheel up

150060

1 1/4"

Blade

± 1 mm (0.04”)

3.0 mm (0.12”)

Содержание LT15M2 D10










































































































Результаты поиска

Содержание LT15M2 D10

Отзывы:

Wood-mizer LT15M2 D10, Руководство пользователя, Страница: 93 / 105

Результаты поиска

Содержание LT15M2 D10

Отзывы: