Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 15

Страница: 15 / 105

Safety & General Information

Sawmill Operation

Safety & General Information

15doc080213

1-3

WARNING!

Secure all loose clothing and jewelry before operating

the sawmill. Failure to do so may result in serious injury or death.

WARNING!

Always make sure log is clamped securely before

sawing. Failure to do so may result in serious injury or death.

WARNING!

Use ONLY water with the water lube accessory. Never

use flammable fuels or liquids. If these types of liquids are necessary
to clean the blade, remove it and clean with a rag. Failure to do so
may result in serious injury or death.

CAUTION!

Be sure the log clamps are all the way down before

loading a log onto the bed. Failure to do so may result in machine
damage.

CAUTION!

Before loading a log, be sure the cutting head is moved

far enough forward so the log does not hit it. Failure to do so may
result in machine damage.

CAUTION!

Do not try to force the saw head beyond its upper and

lower travel limits. Damage to the up/down system may result.

CAUTION!

Be sure to stop the blade when returning the carriage.

This will not only prevent the blade from being pulled off and ruined
by a wood sliver, but also will increase the life of the blade.

CAUTION!

Never clean the blade or the blade wheels with a brush

or a scraper during sawmill operation.

CAUTION!

Before installation of the blade, inspect it for damage and

cracks. Use only properly sharpened blades. Always handle the
blade with extreme caution. Use suitable carrier equipment for
transporting the blades.

CAUTION!

Always wear gloves when handling the blade. Never

grab the blade with bare hands!

CAUTION!

If the blade breaks during sawmill operation, push the

EMERGENCY STOP button to stop the blade engine and wait
10 seconds before opening the blade housing cover.

CAUTION!

The sawmill’s work-stand should be equipped with a 4 kg

or bigger dry powder extinguisher.

Содержание LT15M2 D10










































































































Результаты поиска

Содержание LT15M2 D10

Отзывы:

Wood-mizer LT15M2 D10, Руководство пользователя, Страница: 15 / 105

Результаты поиска

Содержание LT15M2 D10

Отзывы: