manualshive.com logo in svg

Wood-mizer LT15M2 D10, Руководство пользователя, Страница: 21 / 105

Поделиться
Скачать
Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 21

Safety & General Information

Belt Sizes

Safety & General Information

15doc080213

1-9

1

1.5

Belt Sizes

See Table 1-2.   

Belt sizes for the LT15 are shown.

1.6

Blade Sizes

See Table 1-3.   

Wood-Mizer TRU•SHARP™ offers three types of blades to provide efficient

sawing for all models of sawmills. The engine/motor size of your sawmill and the type of wood you
saw should determine which blade you choose for optimum performance.

See 

The Blade Handbook

 for blade hook angle, tooth height, and tooth set specifications.

Description

Belt Size

Wood-Mizer 

Part #

Engine Drive Belt (G18, D10)

BX87

097448

Blade Pulley Belts

B57

 1

1 

To insure proper blade tracking, use Goodyear, Dayco Super II, or

Browning belts only.

P04185

TABLE 1-2

Engine/Motor Size

Recommended Blade For Sawing:

Softwood

Hardwood

Frozen or Hard-to-Cut 

Wood

5 hp - 15hp

B275IH1030
B275IH741030

B375IH929

B375IH929

 1

1 

TRU•SHARP™ “F” blades use a 9/29 profile (9° hook angle and 29° back angle) and are de-

signed to cut frozen and/or extremely dense, hard-to-cut wood. Standard TRU•SHARP™
blades use a 10/30 profile.

16hp or more

B376IH1030
B376IH741030

B275IH1030
B275IH741030
B376IH1030
B376IH741030

 2

2 

Customer may choose preferred blade.

B375IH929 

1

Electric Motor

B376IH1030
B376IH741030

B275IH1030
B275IH741030
B376IH1030
B376IH741030 

2

B375IH929

 1

TABLE 1-3

Содержание LT15M2 D10










































































































Отзывы:

Нет отзывов