Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 105

Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 54

Setup & Operation

Sawmill Setup

3

3-6

15doc080213

Setup & Operation



Recheck the vertical alignment of each blade wheel. Readjust if necessary.

10.

Adjust the spacing between each blade guide roller flange and the back of the blade.

11.

Adjust the horizontal angle of the blade guides.

See Section 6.10

12.

Adjust the blade deflection (

See Section 6.7

) and the vertical angle of the blade guides

See Section 6.8

HINT:

It is best to preliminarily set the blade deflection so that it is 3 - 4 mm, then adjust the blade

guides in the vertical plane and make the final adjustments to the blade deflection. The proper
blade deflection is 6 mm. After adjusting the blade deflection, recheck the vertical alignment of the
blade guides and adjust if necessary.

13.

Install the blade height scale. To do that, first measure the distance from the bottom edge on
a down-set tooth of the blade to the top of the bed rail. Then stick the blade height scale on the
mounting bracket so that it indicates the true distance from the blade to the bed. Adjust the scale if
necessary.

See Section 6.12

FIG. 3-6

150076

To tilt wheel up, tighten top

screw (loosening ealier

bottom screw). To tilt wheel

down, tighten bottom screw

(loosening ealier top screw).

Alignment Tool

«
...
52
53
54
55
56
...
»

Содержание LT15M2 D10










































































































Отзывы:

Нет отзывов