manualshive.com logo in svg

Wood-mizer LT15M2 D10, Руководство пользователя, Страница: 67 / 105

Поделиться
Скачать
Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 67

Setup & Operation

Feed Operation

Setup & Operation

15doc080213

3-19

3

3.10.2 Optional Electric Feed System

The feed system includes an electric motor with gear which moves the saw head using a steel
strand. The speed at which the saw head travels forward is adjusted by the feed rate switch. 

See Figure 3-3. 

Saw Head Feed Rate

The saw head feed rate switch controls the speed at which the saw head travels forward.  Turn the
switch clockwise to increase speed. Turn it counterclockwise to reduce speed. Reverse feed speed
is constant.

Saw Head Forward and Reverse

The power feed switch controls the direction in which the saw head travels. Turn the switch upward
to move the saw head forward. Turn the switch down  to move the saw head backward. 

NOTE:

 Always disengage the blade before returning the saw head and raise the saw head slightly

to make sure the blade clears the log.

Feed Rate

HINT: 

To get a straight cut in the first part of the log, feed the blade into the log at a slow speed.

This stops the blade from flexing and dipping up or down. Turn the saw head feed rate switch to a
slow speed until the whole width of the blade has entered the cut. Then use the saw head feed rate

FIG. 3-3

Saw Head 

Forward

Saw Head 

Reverse

Feed Rate 

Adjustment

Содержание LT15M2 D10










































































































Отзывы:

Нет отзывов