manualshive.com logo in svg

Wood-mizer LT15M2 D10, Руководство пользователя, Страница: 66 / 105

Поделиться
Скачать
Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 66

Setup & Operation

Feed Operation

3

3-18

15doc080213

Setup & Operation

See Figure 3-2. 

HINT: To get a straight cut in the first part of the board, feed the blade into the log at a slow
speed. This stops the blade from flexing and dipping up or down. Use a slow speed until the
whole width of the blade has entered the cut. Then increase the feed rate as desired.
Maximum feed rate varies with width and hardness of the wood. Over-feeding results in
engine and blade wear, and also produces a wavy cut.

2.

To move the carriage backward, rotate the feed crank counterclockwise, or pull the saw head back.
Always disengage the blade before returning the carriage and raise the carriage slightly to make
sure the blade clears the log.

CAUTION!

 Be sure to stop the blade when returning the carriage.

This will not only prevent the blade from being pulled off and ruined
by a wood sliver, but also will increase the life of the blade.

3.

Make sure that the blade does not catch on the end of the log. Raise the carriage slightly to make
sure the blade clears the log when returned.

HINT:

 Try to stop the blade while the heel of the blade is still on the log. Then bring the carriage

back without adjusting the blade up. This lets you keep the blade at the current height setting so
you can make the next blade height adjustment more quickly.

FIG. 3-2

150214

Turn crank clockwise
for reward feed;
counterclockwise
to return carriage.

Push crank handle
in to engage screws
for feed operation.

Содержание LT15M2 D10










































































































Отзывы:

Нет отзывов