manualshive.com logo in svg

Wood-mizer LT15M2 D10, Руководство пользователя, Страница: 73 / 105

Поделиться
Скачать
Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 73

Setup & Operation

Transporting the Sawmill

Setup & Operation

15doc080213

3-25

3

Not all types of wood require the use of the Water Lube System. When it is needed, use just
enough water to keep the blade clean. This saves water, and lowers the risk of staining the boards
with water. Usual flow will be 1-2 gallons (3.8-7.6 liters) per hour. A squirt of liquid dishwashing
detergent in the water bottle will help clean the blade when cutting wood with a high sap content. 

WARNING! 

Use ONLY water with the water lube accessory. Never

use flammable fuels or liquids. If these types of liquids are necessary
to clean the blade, remove it and clean with a rag. Failure to do so
may result in serious injury or death.

Before removing the blade, engage the clutch/brake lever. Let the blade spin with water running on
it for about 15 seconds. This will clean the blade of sap buildup. Wipe the blade dry with a rag
before storing or sharpening.

If you are sawing in freezing temperatures, remove the water lube bottle from the sawmill when
done sawing and store it in a warm place. Blow any remaining water from the water lube hose.

3.15 Transporting the Sawmill

The assembled sawmill can be transported in an appropriately equipped pickup truck:

1.

Adjust the saw head up just far enough so it will clear the sides of your truck bed when loaded.
Do not adjust the saw head so high that the sawmill will tip easily while being loaded.

2.

Move the saw carriage to one end of the frame. Engage the travel lock pin to prevent the saw
carriage from moving. Pull the pin and rotate and release so the roll pin seats in the locking position
notch.

Содержание LT15M2 D10










































































































Отзывы:

Нет отзывов