manualshive.com logo in svg

Wood-mizer LT15M2 D10, Руководство пользователя, Страница: 56 / 105

Поделиться
Скачать
Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 56

Setup & Operation

Replacing The Blade

3

3-8

15doc080213

Setup & Operation

15.

Adjust the cam engaging the limit switch as well as the saw head stop bolt so that the saw head
stops moving at its lower travel limit, i.e. at the height of 25 mm above the bed.  

3.2

Replacing The Blade

DANGER!

 Always disengage the blade and shut off the sawmill

engine before changing the blade. Failure to do so will result in
serious injury.

WARNING!

 Always wear gloves and eye protection when handling

bandsaw blades. Changing blades is safest when done by one
person! Keep all other persons away from area when coiling,
carrying or changing a blade. Failure to do so may result in serious
injury.

Adjust the blade guide arm all the way open.

Open the two blade housing covers that cover the blade wheels. Turn the blade tension handle to
release the blade tension until the wheel is pulled in and the blade is lying loose in the blade
housing. Lift the blade out of the blade housing.

FIG. 3-6

Loosen bolts and adjust cam 
engaging limit switch

Loosen the nut and adjust 
the stop bolt

Limit Switch

Содержание LT15M2 D10










































































































Отзывы:

Нет отзывов