Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 105

Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 53

Setup & Operation

Sawmill Setup

Setup & Operation

15doc080213

3-5

3

idle-side blade wheel.

See Figure 3-5.



Remove the tool from the blade and reattach it near the inner blade guide. Measure from the
tool to the bed rail at both ends of the tool. If the measurements at the front and rear ends of
the tool differ by more than 1/16” (1.5 mm), adjust the vertical tilt of the drive-side blade
wheel.

See Figure 3-6.

See Figure 3-5.

To tilt the idle-side blade wheel up, loosen the bottom adjustment screw 1/2 turn.

Loosen the nut on the top adjustment screw and tighten the screw. Tighten the top and bottom
nuts.

To tilt the wheel down, loosen the top adjustment screw 1/2 turn. Loosen the nut on the bottom
adjustment screw and tighten the screw. Tighten the top and bottom nuts.

See Figure 3-6.

To tilt the drive-side blade wheel down, loosen the top adjustment screw, loosen

the nut on the bottom adjustment screw and tighten the bottom screw. Tighten the top and bottom
nuts.

To tilt the wheel up, loosen the bottom adjustment screw, loosen the nut on the top adjustment
screw and tighten the top screw. Tighten the top and bottom nuts.

FIG. 3-5

To tilt wheel up, tighten top

screw (loosening ealier

bottom screw). To tilt wheel

down, tighten bottom screw

(loosening ealier top screw).

«
...
51
52
53
54
55
...
»

Содержание LT15M2 D10










































































































Отзывы:

Нет отзывов