manualshive.com logo in svg

Wood-mizer LT15M2 D10, Руководство пользователя, Страница: 92 / 105

Поделиться
Скачать
Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 92

Alignment

Blade Wheel Alignment

6

6-4

15doc080213

Alignment

5.

Recheck the vertical tilt of the drive-side blade wheel with the blade guide alignment tool. Readjust
the blade wheel as necessary until the front and rear of the tool are the same distance from the
bed rail (within 1/16" [1.5 mm]).

6.

Remove the tool from the blade and reattach it near the outer blade guide assembly.

7.

Measure from the tool to the bed rail at both ends of the tool. If the measurements at the front and
rear ends of the tool differ by more than 1/16" (1.5 mm), adjust the vertical tilt of the idle-side blade
wheel.

See Figure 6-4. 

 Use the vertical adjustment screws to adjust the idle-side blade wheel. To tilt the

wheel up, loosen the bottom adjustment screw one quarter turn. Loosen the jam nut on the top
adjustment screw and tighten the screw. Tighten the top and bottom jam nuts.

To tilt the wheel down, loosen the top adjustment screw one quarter turn. Loosen the jam nut on
the bottom adjustment screw and tighten the screw. Tighten the top and bottom jam nuts.

FIG. 6-3

150076

To tilt wheel up, tighten top 

screw (loosening ealier 

bottom screw). To tilt wheel 

down, tighten bottom screw 

(loosening ealier top screw).

Alignment 

Tool

Содержание LT15M2 D10










































































































Отзывы:

Нет отзывов