manualshive.com logo in svg

Wood-mizer LT15M2 D10, Руководство пользователя, Страница: 79 / 105

Поделиться
Скачать
Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 79

Maintenance

Wear Life

Maintenance

15doc080213

4-1

4

SECTION 4   MAINTENANCE

This section lists the maintenance procedures that need to be performed. 

The Short Interval Maintenance Schedule lists procedures that need to be performed every
4, 8 or 25 hours.The Maintenance Log lists procedures that need to be performed every
50, 100, 200, or 1000 hours. Keep track of machine maintenance by filling in the machine hours
and the date you perform each procedure. 

This symbol

 identifies the interval (hours of operation) at which each maintenance procedure

should be performed.

Be sure to refer to option and engine manuals for other maintenance procedures.

4.1

Wear Life

See Table 4-1.   

This chart lists estimated life expectancy of common replacement parts if proper

maintenance and operation procedures are followed. Due to the many variables which exist during
sawmill operation, actual part life may vary significantly. This information is provided so that you
may plan ahead in ordering replacement parts.

4.2

Sawdust Removal

Remove the excess sawdust from the blade wheel housings and sawdust chute every blade
change.

4.3

Carriage Track & Rollers

See Figure 4-1. 

1.

Clean the track rails to remove any sawdust and sap buildup every eight hours of operation. 

2.

Remove sawdust from the track roller housings. Remove the track roller housing covers and brush

Part Description

Estimated 

Life

B57 Blade Wheel Belts

500 hours

Blade Guide Rollers

1000 hours

Drive Belt

1250 hours

Power Feed System Steel Strand

500 hours

TABLE 4-1

0

8

8

Содержание LT15M2 D10










































































































Отзывы:

Нет отзывов