Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 105

Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 65

Setup & Operation

Feed Operation

Setup & Operation

15doc080213

3-17

3

3.

Start the engine as instructed in the engine manual.

See Figure 3-15.

The tensioner handle is located next to the engine.

4.

To engage the blade, press the safety switch with your left hand and hold it down. Then push the
tensioner handle forward until it locks. This engages the drive mechanism and increases the
engine speed to full throttle. Keep the safety switch pressed all the time the tensioner is engaged
and the blade is driven in order to prevent the sawmill operator from getting to the path of the
blade. If the safety switch is released the engine stops and it needs to be restarted.

5.

To disengage the blade, pull the tensioner handle. This disengages the drive belt and returns the
engine to idle. The safety button can be released now, the engine continues to run idle.

3.10 Feed Operation

3.10.1 Standard Manual Feed System

The feed system includes a hand crank to move the carriage forward or backward.
The speed at which the carriage travels forward depends on how fast you turn the feed
crank.

1.

To move the carriage forward, push the crank handle in to engage the screw heads and rotate the
feed crank clockwise.

FIG. 3-15

15B026-2C

To engage the
blade, push the
clutch handle
forward.

«
...
63
64
65
66
67
...
»

Содержание LT15M2 D10










































































































Отзывы:

Нет отзывов