Wood-mizer LT15M2 D10 Скачать руководство пользователя страница 58

Страница: 58 / 105

Setup & Operation

Tracking The Blade

3-10

15doc080213

Setup & Operation

CAUTION!

Release the blade tension when the mill is not in use.

See Table 3-1.

he recommended tension for different blades is shown below.

3.4

Tracking The Blade

Make sure the blade housing covers are closed and all persons are clear of the blade.

Start the engine (or motor).

Pull lightly on the clutch handle, rotating the blade until the blade positions itself on the wheels.

WARNING!

Do not spin the blade wheels by hand. Spinning the

blade wheels by hand may result in serious injury.

Release the clutch handle to stop the blade. Turn off the engine and check the position of the blade
on the blade wheels.

See Figure 3-8.

Position 1 1/4” wide blades so the gullet is 1/8" (3.0 mm) out from the edge of the

blade wheel (±1/32 [.75 mm]).

Blade Type

Blade Dimensions

Tension range

Width (mm)

Height (mm)

PSI

Bar

275

1.07

1015-1088

70-75

375

1.14

1088-1160

75-80

2735

1.07

1160-1233

80-85

TABLE 3-1

FIG. 3-8

1 1/4"

Blade

± 1 mm (0.04”)

3.0 mm (0.12”)

Содержание LT15M2 D10










































































































Результаты поиска

Содержание LT15M2 D10

Отзывы:

Wood-mizer LT15M2 D10, Руководство пользователя, Страница: 58 / 105

Результаты поиска

Содержание LT15M2 D10

Отзывы: