manualshive.com logo in svg

WinGD X62DF, Руководство по обслуживанию

Поделиться
Скачать
WinGD X62DF Скачать руководство пользователя страница 709

PROCEDURE

1

Put the proximity sensor (002, 

Figure 12-18

) into the sensor adapter (001).

2

Turn the proximity sensor until the end of the proximity sensor is 3.5 ±0.5 mm from the
mark (004).

3

Tighten the locknut (003).

4

Connect the electrical connection to the proximity sensor (002).

5

On the local control panel, make sure that no failure shows.

6

If applicable, make sure that no failure shows in the control box of the Lenze Drive
system.

NOTE:

Different designs have a Lenze Drive system installed. This system has a
control box installed in the control cabinet. The control box shows signal
failures.

Fig 12-18  Proximity sensor - install

I

I

00585

3.5 ±0.5 mm

I - I

ZS5401C - DRVING END

002

ZS5405C - FREE END

003

001

004

CLOSE UP

•

None

X72DF

AA00-7762-00AAA-720A-A

Maintenance Manual

Electric balancer sensor unit - install the proximity sensor

Winterthur Gas & Diesel Ltd.

- 709 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды