WinGD X62DF Скачать руководство пользователя страница 3

Страница: 3 / 902

Table of contents

Maintenance Manual - change record. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3

Technical documentation set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4

Data module codes (procedural data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.5

Data module codes (descriptive data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6

Data module codes (illustrated parts data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7

About this book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.8

About the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.9

List of abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety

2.1

Safety precautions and safety rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2

Safety precautions and safety rules for natural gas. . . . . . . . . . . . . . . . . . . . . . . . . . . .

General data for maintenance

3.1

Lifting tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2

Jointing compounds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3

Clearances - general. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4

Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5

Torque values - standard screws. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

General mainteance procedures

4.1

Do maintenance work - general procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2

Tighten a round nut with a pre-tensioner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3

Loosen a round nut with a pre-tensioner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4

Do a check of the pre-tension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance schedule

5.1

Maintenance schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

100

Group 1 - Engine frame and bearings

6.1

Bedplate

6.1.1

Bedplate - do a check of the foundation bolts. . . . . . . . . . . . . . . . . . . . . . . . . . . .

102

6.2

Main bearing

6.2.1

Main bearing - remove the cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

104

6.2.2

Main bearing - install the cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

110

6.3

Main bearing shell

6.3.1

Main bearing shell - remove. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

116

X72DF

Maintenance Manual

Winterthur Gas & Diesel Ltd.

- 3 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды