WinGD X62DF страница 197 Скачать руководство пользователя

Страница: 197 / 902

PROCEDURE

If necessary, remove the union (007,

Figure 7-14

) on the lubricating quill (002).

Fig 7-14

Lubricating quill

Attach the distributing piece (004) to the HP oil pump (006).

Attach the connection nipple (008) to the lubricating quill (002).

Connect the HP hose (003) to the nipple (008) and to the distributing piece (004).

Hold the lubricating quill (002) so that the non-return valve (001) points up and points
away from your body.

Operate the HP oil pump (006) until oil that has no air flows out.

Open the relief valve (005) to decrease the pressure to 2.0 bar.

Close the relief valve (005).

Hold the lubricating quill (002) in a horizontal position so that it points away from your
body.

Operate the HP oil pump (006) to increase the pressure in steps of 1.0 bar until the non-
return valve (001) opens.

Record the pressure shown on the pressure gauge (004).

NOTE:

The minimum permitted pressure to open the non-return valve is 4.25 bar. If
necessary, replace the defective lubricating quill (002).

Open the relief valve (005) to release the pressure to zero.

Remove the nipple (008) and the HP hose (003) from the lubricating quill (002).

CLOSE UP

•

None

X72DF

AA00-2138-00AAA-340A-A

Maintenance Manual

Lubricating quill - do a functional test

Winterthur Gas & Diesel Ltd.

- 197 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Похожие инструкции для X62DF

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Похожие инструкции для X62DF

Бренды по названию

Популярные бренды