WinGD X62DF страница 120 Скачать руководство пользователя

Страница: 120 / 902

Remove the bearing shell.

4.1

Attach the shackle (004,

Figure 6-11

) to the position shown.

4.2

Attach the chain block (003) to the shackle (004).

4.3

Remove the Allen screws (007) from the top of the bearing shell (002).

4.4

Attach the turning out device (009) to the bearing shell (002).

4.5

Put the wire ropes (006) around the edges of the main bearing shell (002).

4.6

Attach the wire ropes to the lifting plate (008).

4.7

Attach the chain block (003) to the middle hole in the lifting plate (008).

4.8

Operate the chain block (003) to turn the bearing shell (002) a sufficient distance
to attach the lifting tool.

4.9

Remove the chain block (003) from the lifting plate (008).

4.10

Remove the turning out device (009) and the lifting plate (008).

Fig 6-11

Bearing shell - remove

001

002

003

004

006

007

005

006

009

006

002

008

X72DF

AA00-1134-00AAA-520A-A

Maintenance Manual

Main bearing shell - remove

Winterthur Gas & Diesel Ltd.

- 120 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Похожие инструкции для X62DF

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Похожие инструкции для X62DF

Бренды по названию

Популярные бренды