WinGD X62DF Скачать руководство пользователя страница 474

Страница: 474 / 902

Operate the turning gear to move the piston (001,

Figure 8-67

) until you can see the

piston rings (002) through the scavenge ports.

Fig 8-67

Piston ring - clearance

001

002

001
002

003

002

001

002

001

Worn edge on
chrome-ceramic layer

Measure the clearance of the first piston ring at an applicable position as follows:

11.1

Measure the clearance X1 and X2 with the feeler gauge.

NOTE:

If there is an edge of worn material on the chrome-ceramic layer or in
the piston groove, you can not fully push the feeler gauge into the
groove.

NOTE:

Clearance X2 can be more than zero, if the piston ring is tilted or if
there is contamination in the piston groove.

11.2

Record the total clearance X = X1 + X2.

If possible do

Step 11

again on different positions of the first piston ring.

Step 11

and

Step 12

again for the other piston rings.

Compare the recorded clearances with the maximum permitted values, refer to section

3.3 Clearances - general

If the clearance is more than the permitted value, do as follows related to the defective
item:

15.1

Replace the defective piston rings.

15.2

Repair the defective piston head.

NOTE:

For the repair of piston heads, speak to the nearest WinGD Service
Center.

Record the data that follow:

•

All dimensions

•

Date of the overhaul

•

Operation hours of the different components

•

Operation hours of the engine.

CLOSE UP

•

None

X72DF

AA00-3403-00AAA-360A-A

Maintenance Manual

Piston (installed) - do checks of the surface and clearances

Winterthur Gas & Diesel Ltd.

- 474 -

Issue 002 2020-10

Содержание X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды

WinGD X62DF, Руководство по обслуживанию

Результаты поиска

Содержание X62DF

Отзывы:

Бренды по названию

Популярные бренды